- Inquiry
Low Profile Floor Transmission Jack
• For lifting and lowering gearboxes and differential units • ldeal for removingtransmissions and gastanks on smallervehicles • Scissor-type design enables precise movement for users to manoeuvre and fit transmission assemblies
PRODUCT PARAMETERS
| Model | TEL02001 |
| Capacity | 450lbs/200kgs |
| Min.Height | 190 mm |
| Max.Height | 590 mm |
| Base Size | 45x42cm |
| N.W./G.W. | 19kgs/20 kgs |
| Package Size | 48cm x 45cm x 20cm |
| QTY/20'CY | 650 pcs |
OTHER MODELS
About the Product
Product Information
This equipment is designed for transmission installation and removal. Universal mounting head provides a wide fore and aft tilt range. Manual operated hydraulic system that includes a bypass system to prevent over-extension and accidental overloading. Low profile design; four heavy-duty steel swivel casters provide easy maneuvering throughout the shop. Fits most transmissions. This product is tested for reliability and safety to meet ASME PASE Standards.
Product Parameters
| Model | TEL02001 |
| Capacity | 450lbs/200kgs |
| Min.Height | 190 mm |
| Max.Height | 590 mm |
| Base Size | 45x42cm |
| N.W./G.W. | 19kgs/20 kgs |
| Package Size | 48cm x 45cm x 20cm |
| QTY/20'CY | 650 pcs |
Matters need attention
Common Problems And Solutions
If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load.
Cleaning:
If the moving parts of the equipment are obstructed, use cleaning solvent or another good degreaser to clean the equipment. Remove any existing rust with a penetrating lubricant.
How the Jack Operates：
With release valve closed, an upward stroke of the jack handle draws oil from the reservoir tank into the plunger cavity. Hydraulic pressure holds the valve closed, which keeps the oil in the plunger cavity. A downward stroke of the jack handle releases oil into the cylinder, which forces the ram out. This raises the saddle. When the ram reaches maximum extension, oil is bypassed back into the reservoir to prevent an over extended ram stroke and possible damage to the jack. Opening the release valve allows oil to flow back into reservoir. This releases hydraulic pressure on the ram, which results in lowering the saddle.
Storing the Jack:
1. Lower the hydraulic ram to lowest position.
2. Leave lowering valve open.
3. Store in a dry location, recommended indoors.
Note: If the jack is stored outdoors, be sure to lubricate all parts before and after use to ensure the jack stays in good working condition. Always store jack in the fully retracted postion when stored in outdoor or caustic enviroments that can cause corrosion and/or rust.
Ingredients-
Premium hydraulic oil. P.reventing from oil leakage
Hydraulics are powered with high quality oil,which offers better corrosion resistance and high/low temperature flexibility,allowing unit to operate at temperatures between 40 degrees F and 105 degrees F.
Automatic welded
This valve is welded in fine steel, having the features of handy to operate, good seal, reliable performance and having the function of automatic air-locking dropping material.
High Stregth Steel
Constructed of high-grade steel and built to exacting standards for quality and durability.
You May Also Like
Model
3.5 Ton Full-rise Scissor Lift QJYJ35DF
0.75/0.55/1.1kw Car Tire Changer
0.75/0.55/1.1kw Car Tire Changer
560KG Gear-Driven Rotating Engine Stand
680KG Gear-Driven Rotating Engine Stand
500KG Structure Engine Stand
Features
• Mechanical safety lockengaged automaticallywhen lowering • Low voltage control unit • Platform extending for long vehicles • Hight limit switch • Easy access grease nipple design • Secondary descending alarm& stop • Rubber pads115x100x70mm 4pcs • Infrared synchronization protection system • Drive-by-wire control
• Full automatic penumatic tilting column. Independent right helper arm, with pneumatic tire lifting device 360 rotary tire pressing helper arm. Four angle directional adjustable tire pressing shovel.
• Full automatic penumatic tilting column. Independent right helper arm, with pneumatic tire lifting device 360 rotary tire pressing helper arm. Four angle directional adjustable tire pressing shovel.
• The wheels construction for more stability and esy rolling. • Adjustable mounting arms, accommodate a majority of engine blocks, both foreign and domestic. • Mounting plate rotates 360 degree and can be locked in 8 different positions. • Heavy gauge tubular steel construction. • Roll-around engine stand assembles easily.
• The wheels construction for more stability and esy rolling. • Adjustable mounting arms, accommodate a majority of engine blocks, both foreign and domestic. • Mounting plate rotates 360 degree and can be locked in 8 different positions. • Heavy gauge tubular steel construction. • Roll-around engine stand assembles easily.
• The wheels construction for more stability and esy rolling. • Adjustable mounting arms, accommodate a majority of engine blocks, both foreign and domestic. • Mounting plate rotates 360 degree and can be locked in 8 different positions. • Heavy gauge tubular steel construction. • Roll-around engine stand assembles easily.