- Inquiry
6 Ton Welded Bottle Jack
• Steel plate instead of cast iron for environment protection • Preventing from oil leakage • Oil remaining clear after using
PRODUCT PARAMETERS
| Model | TCH90604D |
| Capacity | 6 Ton |
| Min.Height | 185 mm |
| Lift Height | 115 mm |
| Adjustable Height | 60 mm |
| N.W./G.W. | Color Box: 3.88/4.29 kg |
| Package Size | Color Box: 260x245x220 mm |
| QTY/CTN | 4 pcs |
| QTY/20'CY | Color Box: 4848 pcs |
| A | 185 mm |
| C | 115 mm |
| D | 60 mm |
| B | 360 mm |
| ExF | 90x110 mm |
OTHER MODELS
About the Product
Product Information
This BIGRED product has a single hydraulic pump piston that effortlessly raises the lift arm. Pump piston dust shields and wiper seals protect the hydraulic system from contaminants. The jack features an overload valve bypass system to prevent jack damage and user injury. Compact design allows use in confined spaces. Easily fits under low vehicles. This product is tested for reliability and safety.
Product Parameters
| Model | Capacity | Min.Height (mm) |
Lift Height (mm) |
Adjustable Height(mm) |
N.W./G.W. (kg) |
Package Size (mm) |
QTY/CTN (pcs) |
QTY/20'CY (pcs) |
A | C | D |
B |
ExF |
| (mm) | |||||||||||||
| TCH90204D | 2Ton | 150 | 80 | 48 | Color Box: 2.31/2.38 | Color Box: 340x230x185 | 6 | Color Box: 7944 | 150 | 80 | 48 | 278 | 85x90 |
| TCH90304D | 3Ton | 180 | 105 | 60 | Color Box: 2.5/2.56 | Color Box: 340x230x210 | 6 | Color Box: 7404 | 180 | 105 | 60 | 345 | 85x90 |
| TCH90404D | 4Ton | 180 | 110 | 60 | Color Box: 3.11/3.29 | Color Box: 355x240x220 | 6 | Color Box: 5970 | 180 | 110 | 60 | 350 | 90x100 |
| TCH90504D | 5Ton | 185 | 115 | 60 | Color Box: 3.14/3.34 | Color Box: 240x240X220 | 4 | Color Box: 6012 | 185 | 115 | 60 | 360 | 90x100 |
| TCH90604D | 6Ton | 185 | 115 | 60 | Color Box: 3.88/4.29 | Color Box: 260x245x220 | 4 | Color Box: 4848 | 185 | 115 | 60 | 360 | 90x100 |
| TCH90804D | 8Ton | 190 | 110 | 60 | Color Box: 4.45/4.90 | Color Box: 275x245x220 | 4 | Color Box: 4252 | 190 | 110 | 60 | 360 | 100x115 |
| TCH91004D | 10Ton | 190 | 110 | 60 | Color Box: 5.21/5.35 | Color Box: 290x280x225 | 4 | Color Box: 3636 | 190 | 110 | 60 | 360 | 110x120 |
| TCH91204D | 12Ton | 200 | 120 | 60 | Color Box: 6.06/6.20 | Color Box: 440x160x235 | 3 | Color Box: 3123 | 200 | 120 | 60 | 380 | 120x125 |
| TCH91504D | 15Ton | 205 | 125 | 60 | Color Box: 7.15/7.30 | Color Box: 320x165x240 | 2 | Color Box: 2648 | 205 | 125 | 60 | 390 | 120x135 |
| TCH91604D | 16Ton | 205 | 125 | 60 | Color Box: 7.17/7.30 | Color Box: 320x165x240 | 2 | Color Box: 2596 | 205 | 125 | 60 | 390 | 120x135 |
| TCH92004D | 20Ton | 220 | 140 | 60 | Color Box: 8.22/8.40 | Color Box: 330x175x265 | 2 | Color Box: 2324 | 220 | 140 | 60 | 420 | 130x145 |
| TCH93204D | 32Ton | 230 | 130 | 0 | Color Box: 13.95/14.31 | Color Box: 205x195x255 | 1 | Color Box: 1315 | 230 | 130 | 0 | 360 | 160x175 |
| TCH95004D | 50Ton | 230 | 130 | 0 | Color Box: 18.70/19.35 | Color Box: 240x215x260 | 1 | Color Box: 990 | 230 | 130 | 0 | 360 | 175x205 |
Matters need attention
Common Problems And Solutions
1.When lifting heavy weights, the mandril fails to rise to the maximum route. When the jack reaches a certain height, and the maximum route is not reached, the mandril cannot rise up any more, which indicates that there is a lack of working oil in the jack, and it should be replenished.
2. The mandril wobbles while rising. Generally the oil return valve is not closed tightly; we can tighten oil return valve needle in counterclockwise direction. If it is still unstable, check whether there is any oil leakage around the pressure rod; if the oil leaks, it indicates that the seal ring of the mandril is damaged, and it should be replaced. If there is no oil leakage, confirm again whether the oil return valve and the inlet valve is already locked, and also check sealing gasket conditions in the cylinder end joint of pressure rod; if all the above is normal, then it indicates that the seal ring is damaged, or the fixed screw is loosening, we should replace it or tighten the screw.
3. The mandril fails to rise while no-load. First check the oil amount of the jack, and we should add oil when insufficient. If jack is not short of oil, we can loosen the oil return valve needle of the jack, remove the oil plug of oil filling port, then trample on the jack base by our feet, repeatedly pull up the mandril and press down again by our hands for several times, in order to exhaust air; after the above actions are completed, tighten the oil plug of oil filling port and oil return valve tightly, and then try again the no-load mandril; if the mandril still cannot rise, lay jack flat, remove the oil return valve, check whether the valve and seat contact well; if there is dirt, it should be removed; if there is pit, slot and uneven, it should be replaced. Finally check whether the oil inlet valve is well sealed and the sealing ring of mandril is damaged or falls off. If any, replace it in time.
4. Oil leakage, can be seen by visual observation. The oil leakage area of the jack is usually in the base and the cylinder joint, around the mandril, in the lock thread of the oil return valve, in the fixed oil plug of the oil filling port, around pressure rod etc. The cause of oil leakage is usually the damage of sealing gasket, it must be replaced in time.
Ingredients-
Premium hydraulic oil. P.reventing from oil leakage
Hydraulics are powered with high quality oil,which offers better corrosion resistance and high/low temperature flexibility,allowing unit to operate at temperatures between 40 degrees F and 105 degrees F.
Automatic welded
This valve is welded in fine steel, having the features of handy to operate, good seal, reliable performance and having the function of automatic air-locking dropping material.
High Stregth Steel
Constructed of high-grade steel and built to exacting standards for quality and durability.
You May Also Like
Model
3.5 Ton Full-rise Scissor Lift QJYJ35DF
0.75/0.55/1.1kw Car Tire Changer
0.75/0.55/1.1kw Car Tire Changer
500KG Structure Engine Stand
800KG Gear-Driven Rotating Engine Stand
680KG Gear-Driven Rotating Engine Stand
Features
• Mechanical safety lockengaged automaticallywhen lowering • Low voltage control unit • Platform extending for long vehicles • Hight limit switch • Easy access grease nipple design • Secondary descending alarm& stop • Rubber pads115x100x70mm 4pcs • Infrared synchronization protection system • Drive-by-wire control
• Full automatic penumatic tilting column. Independent right helper arm, with pneumatic tire lifting device 360 rotary tire pressing helper arm. Four angle directional adjustable tire pressing shovel.
• Full automatic penumatic tilting column. Independent right helper arm, with pneumatic tire lifting device 360 rotary tire pressing helper arm. Four angle directional adjustable tire pressing shovel.
• The wheels construction for more stability and esy rolling. • Adjustable mounting arms, accommodate a majority of engine blocks, both foreign and domestic. • Mounting plate rotates 360 degree and can be locked in 8 different positions. • Heavy gauge tubular steel construction. • Roll-around engine stand assembles easily.
• The wheels construction for more stability and esy rolling. • Adjustable mounting arms, accommodate a majority of engine blocks, both foreign and domestic. • Mounting plate rotates 360 degree and can be locked in 8 different positions. • Heavy gauge tubular steel construction. • Roll-around engine stand assembles easily.
• The wheels construction for more stability and esy rolling. • Adjustable mounting arms, accommodate a majority of engine blocks, both foreign and domestic. • Mounting plate rotates 360 degree and can be locked in 8 different positions. • Heavy gauge tubular steel construction. • Roll-around engine stand assembles easily.